CAT D6 XL WH
Caterpillar D6 XL Waste Handling Dozer?
CAT C9.8 ACERT Engine
Engine Block Heater
Automatic 4 Speed Transmission
Cab (ROPS) w/ A/C
Differential Steer
Engine Air Pre-Cleaner
Waste Handling (Landfill) Arrangement
SALT Undercarriage
24" Trapezoidal Shoes
Final Drive Seal Guards
Pivot Shaft Seal Guards
SU Blade w/ Trash Rack
Automatic Reversing Fan
Drawbar
Fuel Tank Guards
Heavy Duty Bottom Guards
CAT Slope Indicate
LED Flood Light Arrangement
Ripper Ready
Ansul Fire Suppression
Powered Cab Pre-Cleaner
Rated at 255 HP
Weight 54,000 LBS
CAT D6 XL WH with Factory Waste Handling (Landfill) Arrangement, Ex Municipal Unit, Recent Transmission & Torque Converter Rebuild, Complete Machine Reconditioning by Marcel Equipment, SU Blade w/ Trash Rack, 24" Trapezoidal Shoes, Pivot Shaft Seal Guards, Ansul Fire Suppression, All Needed Servicing & Repairs Have Been Completed.
The following are repairs completed by the CAT Dealer prior to Marcel Equipment owning this CAT D6 XL Waste Dozer;
At 513 hours, performed 500 hour service
At 1,032 hours, performed 1,000 hour service
At 1,491 hours, performed 500 hour service
At 2,094 hours, performed 2,000 hour service
At 2,513 hours, performed 500 hour service
At 3,091 hours, performed 1,000 hour service
At 3,538 hours, performed 500 hour service
At 4,051 hours, performed 2,000 hour service
At 4,542 hours, performed 500 hour service
At 5,071 hours, performed 1,000 hour service
At 5,580 hours, performed 500 hour service
At 5,651 hours, performed DPF service & valve set
At 5,651 hours, installed NEW DEF injector & spark plug
At 5,651 hours, installed NEW thermostat
At 6,048 hours, performed 2,000 hour service
At 6,305 hours, performed update for condenser fans
At 6,305 hours, REBUILT both lift cylinders
At 6,543 hours, performed 500 hour service
At 6,719 hours, installed NEW a/c condenser
At 6,875 hours, installed NEW injector wiring harness
At 6,913 hours, installed NEW DPF pressure sensors
At 7,046 hours, performed 1,000 hour service
At 7,083 hours, installed NEW ARD head & spark plug
At 7,358 hours, installed NEW undercarriage
At 7,414 hours, installed NEW engine ECM
At 7,502 hours, performed 500 hour service
At 8,048 hours, performed 2,000 hour service
At 8,261 hours, installed NEW parking brake solenoid
At 8,261 hours, installed NEW NOX sensors
At 8,261 hours, installed NEW DEF manifold
At 8,510 hours, performed 500 hour service
At 8,792 hours, replaced oil cooler
At 8,792 hours, REBUILT transmission oil pump
At 8,792 hours, REBUILT transmission
At 8,792 hours, REBUILT torque converter
At 9,027 hours, performed 1,000 hour service
Marcel Equipment completed the following on this CAT D6 XL WH for sale?;
Upon arrival to our yard, machine was stripped for power washing
Machine was inspected visually & operationally
Engine oil filter was cut open - clean
Transmission filter was cut open - clean
Hydraulic filter was cut open – clean
Magnets & suction screens checked - clean
Final drive oils were checked - levels good & oils clean
Engine was serviced
Transmission, hydraulic & final drive oils were changed
Replaced DEF pump & tank filters
The following pressures were taken to ensure within OEM spec;
Engine low/high RPM
Stall speed
Engine oil pressures - high/low
Fuel pressure
Engine boost
Transmission pump pressure - high/low
Transmission lube pressure - high/low
Torque converter inlet & outlet - high/low
Lock-up clutch pressure
Pilot pressure
Main relief pressure
Steering stand-by pressure
Brake pressures
Accumulators
Fan speed - max/min
Steering cut-out
Marcel Equipment completed the following repairs for this D6 XL WH Dozer?;
Completed bearing roll-in for main & rods
Engine oil pump disassembled, inspected & resealed
Resealed engine oil pan
Installed NEW a/c dryer
Replaced required hoses/lines
Installed NEW window spray nozzles
Installed NEW DEF injector
Installed NEW DEF manifold
Installed NEW bearings for lift cylinder yoke mounts
Had DPF filter field cleaned
Removed & cleaned engine pre-cleaner
Installed NEW track cannon seals
Disassembled, inspected & resealed final drives
Installed NEW final drive seal guards
Resealed starter motor
Tightened blade joints where required w/ NEW pins & bearings
Calibrated blade
Installed belly pans
Completed required cab repairs
HVAC system cleaned & serviced
Batteries tested & connections serviced
Completed required cosmetic & welding repairs
Complete machine was sandblasted, primed, painted & new decals applied
Fire suppression will be certified before shipment
Machine has been completed & is work ready! |