CAT D6N LGP WH
CAT C7.1 ACERT Engine
Powershift/Autoshift Transmission
Cab (ROPS) w/ A/C
Differential Steer
6 Way PAT Blade w/ Trash Rack
All NEW CAT SALT Undercarriage
33" Trapezoidal Shoes
Flood Light Arrangement
Air Turbine Engine Pre-Cleaner
Factory Waste Handling (Landfill) Arrangement
Rear Protection Screen
Rear Striker Bar Box Assembly
Final Drive Seal Guards
Reversing Fan - Flexaire
Ansul Fire Suppression
Heavy Duty Rad Guards
Heavy Duty Bottom Pans
Fuel Tank Guard
Rated at 182 HP
Weight 45,000 LBS
6 Way PAT Blade with Trash Rack, All NEW CAT SALT Undercarriage, 33" Trapezoidal Shoes, Air Turbine Engine Pre-Cleaner, Reversing Fan - Flexaire, Ansul Fire Suppression
The following are repairs completed by the CAT Dealer prior to Marcel Equipment owning the machine;
At 264 hours, 250 hour service completed
At 525 hours, 500 hour service completed
At 793 hours, 750 hour service completed
At 1,098 hours, 1,000 hour service completed
At 1,281 hours, 1,250 hour service completed
At 1,556 hours, 1,500 hour service completed
At 1,899 hours, 1,750 hour service completed
At 2,210 hours, 2,000 hour service completed
At, 2,429 hours, 250 hour service completed
At 3,370 hours, 250 hour service completed
At 3,698 hours, 500 hour service completed
At 4,868 hours, installed NEW a/c compressor & dryer
At 5,067 hours, 250 hour service completed
At 5,525 hours, 250 hour service completed
At 5,535 hours, REBUILT final drives
At 5,759 hours, 500 hour service completed
At 5,993 hours, 750 hour service completed
At 6,257 hours, installed NEW track chains, rollers & sprockets
At 6,288 hours, 2,000 hour service completed
At 6,541 hours, 250 hour service completed
At 6,851 hours, 500 hour service completed
At 6,936 hours, installed NEW a/c condenser fan
At 6,936 hours, installed NEW turbo charger
At 7,080 hours, 750 hour service completed
At 7,346 hours, 1,000 hour service completed
At 7,350 hours, installed NEW Flexaire fan
At 7,764 hours, 1,250 hour service completed
At 8,129 hours, installed NEW clean emissions module
Marcel Equipment completed the following inspections;
Upon arrival, machine was fully stripped for power washing
Full visual & operational inspections were completed
Engine, torque, transmission & hydraulic pressures were taken to ensure within OEM spec
Performance checks were completed
Oils were checked for contaminates
Magnets & suction screens were checked for contaminates
All filters were cut open & inspected for contaminates
Machine was serviced as required
Engine, transmission & hydraulic oils were changed
Final drive oils were change
Marcel Equipment then completed the following repairs;
Installed all NEW CAT undercarriage
Resealed both blade lift cylinders & installed NEW pins & bearings
Final drives were disassembled, inspected & resealed
Resealed both angle cylinders & installed NEW pins & bearings
Resealed angle cylinder & installed NEW pins & bearings
Line bored blade bores as required
REBUILT equalizer bar & installed NEW pins & bushings
Line bored track frame bores
Installed NEW batteries
Serviced battery connections
Installed NEW rear wiper motor
Installed NEW fan blades & resealed hub
Installed NEW engine belt & tensioner
Installed NEW cab heater hoses
Removed hardnose & installed NEW pins & bushings
Installed NEW pivot shaft bearings & resealed
Installed all NEW hydraulic lines for blade cylinders
Installed all NEW powertrain lines
Installed NEW cab fan blower motor
Serviced & cleaned complete HVAC system
Installed NEW a/c accumulator, dryer & compressor
Completed all required cab repairs
Completed all required cosmetic repairs
Machine is now scheduled to be sandblasted & painted. |